Evaluation: GEPRC CineBot25 Cinewhoop – Nearly Excellent however Nonetheless Has a Few Points

Evaluation: GEPRC CineBot25 Cinewhoop – Nearly Excellent however Nonetheless Has a Few Points

I’ve examined many cinewhoops previously few years, and the GEPRC CineBot25 is maybe my present favourite 2.5″ cinewhoop. A lot thought has gone into its design, and the eye to element is solely superb. Whereas it’s not good and has just a few annoying points, as you’ll uncover on this evaluation, these quirks don’t detract from its spectacular efficiency.

A few of the hyperlinks on this web page are affiliate hyperlinks. I obtain a fee (at no additional price to you) for those who make a purchase order after clicking on considered one of these affiliate hyperlinks. This helps assist the free content material for the group on this web site. Please learn our Affiliate Hyperlink Coverage for extra data.

Find out about Cinewhoops: https://oscarliang.com/cinewhoop/

The place to Purchase?

You may get the GEPRC CineBot25 from these distributors:

There are two variations: Normal (non-S) and Sport (S). The S model options bigger 1505 4300KV motors, that are an improve from the 1404 motors in the usual model, delivering extra energy and stability.

Geprc Cinebot25 S Cinewhoop Unbox Accessories Parts

Batteries are usually not included, my suggestions are the Lava 4S 850mAh:

Get some spare propellers for those who plan to crash 🙂


Geprc Cinebot25 S Cinewhoop

  • Body: GEP-CT25 Gray
  • Wheelbase: 115mm
  • Flight Controller (FC): TAKER G4 45A AIO
    • MCU: STM32G473CEU6
    • Gyro: ICM 42688-P
    • Firmware: TAKERG4AIO
  • Motor: SPEEDX2 1505 4300KV
  • ESC: BLHeli 32-bit 45A
  • Propellers: HQProp DT63mm x4
  • Connector: XT30
  • Official Weight:
    • Normal PNP Model: 138g ±1g
    • Sport PNP Model: 145g ±1g
  • Really helpful Battery: 4S 650mAh – 850mAh LiPo

Nearer Have a look at the Construct High quality

The GEPRC CineBot25 S stands out with a sturdy, smooth design. The digital camera, motor, and flight controller are mounted on the highest plate, which is made out of smooth-layered carbon fiber, providing a light-weight but sturdy really feel.

Geprc Cinebot25 S Cinewhoop Motor Propeller

Under the highest plate is a detachable plastic housing for the VTX and receiver. The digital elements are effectively protected, however the enclosed design may compromise cooling in scorching environments.

Geprc Cinebot25 S Cinewhoop Side

The FPV digital camera is mounted inside a devoted soft-mounted cover that limits excessive digital camera angles however presents ample safety.

Geprc Cinebot25 S Cinewhoop Camera Mount

An exterior HD digital camera could be hard-mounted utilizing the supplied adapter, nevertheless it’s greatest to keep away from including additional weight like a unadorned GoPro. Whereas it might work for sluggish and regular indoor pictures, it compromises outside agility and velocity. The DJI O3 system already offers glorious picture high quality anyway.

Geprc Cinebot25 S Cinewhoop Antenna Mount

Two battery straps of various lengths are included: an extended one for 4S 750mAh and 850mAh batteries, and a shorter one for smaller 4S 650mAh batteries. The drone weighs round 153 grams with out the battery, digital camera, and VTX, which is nearly 10 grams heavier than the BetaFPV Pavo25 V2. Nonetheless, this added weight is comprehensible given the additional plastic used for cover.

With the DJI O3 system put in and a 4S 850mAh LiPo, the whole weight is round 290 grams.

Geprc Cinebot25 S Cinewhoop Bottom

Listed below are some facet by facet comparisons to the BetaFPV Pavo25 V2:

Geprc Cinebot25 S Cinewhoop Compare Pavo25

Geprc Cinebot25 S Cinewhoop Compare Pavo25 Frame Side

Geprc Cinebot25 S Cinewhoop Compare Pavo25 Camera Mount

DJI O3 Setup

Though the CineBot25 helps numerous FPV programs, together with analog and Runcam Hyperlink/Wasp, the soft-mounted digital camera platform is a transparent indication that it’s particularly designed for the DJI O3 system. Different FPV cameras aren’t as prone to jello and vibration because the O3, making further delicate mounting crucial. I actually like GEPRC’s implementation utilizing silicone balls as it really works exceptionally effectively.

Geprc Cinebot25 S Cinewhoop Installing Dji O3 Air Unit Camera

Nonetheless, the digital camera cover can simply pop off throughout crashes, and it’s difficult to reattach as a consequence of how tiny and delicate these silicone balls are. They’re additionally fairly fragile, metallic instruments can simply pierce by means of them. Whereas GEPRC offers some instruments to assist with this, it’s a trouble remembering to deliver them alongside. Zip ties can safe them however will scale back the effectiveness of the delicate mounting.

Geprc Cinebot25 S Cinewhoop Camera Mount Detached Crashes Anti Vibration Silicone Balls

Person Pleasant Design

Top-of-the-line design points of the CineBot25 is how simple it’s to entry the flight controller and DJI O3 USB port. There’s a USB-C port on the rear of the drone, related to the flight controller by way of an extension board.

Geprc Cinebot25 S Cinewhoop Flight Controller Fc Usb C Port Rear

You possibly can entry the DJI O3’s SD card slot and USB-C port by means of a cutout within the plastic housing, and when not in use, you may put the rubber cowl again on to guard it from filth and water.

Geprc Cinebot25 S Cinewhoop Silicone Rubber Cover Dji O3 Usb Sd Card

Geprc Cinebot25 S Cinewhoop Installing Dji O3 Air Unit Access Sd Card Usb C Cover

There’s no must disassemble the drone or use an adapter to entry these USB ports, making it extremely handy. You possibly can inform how a lot thought has gone into the design.

Nonetheless, one small situation is that I couldn’t join or flash the ESC by way of the USB port on the FC extension board. I had to make use of the precise USB port on the FC, which requires disassembling the drone. They may have used a USB-C extension cable like Speedybee did within the Bee35 to keep up compatibility. Nevertheless it’s not an enormous deal because you don’t sometimes must flash your ESC.

Dissembling the drone for restore is simple too.

Geprc Cinebot25 S Cinewhoop Tear Down Take Apart Dissemble

Right here’s an in depth up shot of the flight controller.

Geprc Cinebot25 S Cinewhoop Flight Controller Fc

Flight Efficiency

The CineBot25 S is solely probably the greatest flying 2.5-inch cinewhoops I’ve examined—very steady, well-tuned, and with loads of energy for freestyle.

It’s additionally very environment friendly. I examined mine with LAVA 4S 850mAh LiHV batteries from BetaFPV and bought round 5 to six minutes of flight time (a mixture of aggressive flying and cruising), which may be very spectacular.

The DJI O3 VTX system, paired with a soft-mounted digital camera, offers crisp FPV footage with none jello.

Learn how to Setup

Though initially I used to be impressed by the CineBot25’s design, the setup course of took a bit extra time and effort than anticipated.

O3 Set up

Very first thing is to put in the DJI O3 system contained in the plastic housing. Sadly, there’s no instruction supplied, so that you’ll want to make use of your creativeness. I have to admit it wasn’t simple in any respect as I spent over nearly an hour looking for the easiest way to mount the O3. Finally I made a decision to not use the supplied heatsink and simply mounted the O3 instantly contained in the plastic housing.

Geprc Cinebot25 S Cinewhoop Installing Dji O3 Air Unit

Geprc Cinebot25 S Cinewhoop Installing Dji O3 Air Unit Connect Antenna Extension

Geprc Cinebot25 S Cinewhoop Installing Dji O3 Air Unit Finished

Additionally, in contrast to BetaFPV’s cinewhoops, GEPRC doesn’t present any cable for the O3, however you need to use the unique cable, so it’s not an enormous situation for those who nonetheless have it. Additionally there’s no screws supplied for mounting the digital camera within the cover – you will want M2 3mm.

Lastly, be certain that to tape the UFL extension to keep away from electrical shorts! It they touches the uncovered battery solder pads may fry your O3!

Binding Receiver

Right here I encountered one other situation – the receiver doesn’t get energy from the USB port, you will need to plug in a battery.

I used to be going to flash the newest ExpressLRS firmware to the receiver together with my binding phrase, so I wanted to search out out what goal it makes use of. That was completed by going into WiFi mode (by plugging in battery and wait 60 seconds) and checking on the Net UI .

Receiver goal is: Generic ESP8285 PA 2.4Ghz RX, it comes with 3.3.1 firmware.

Nonetheless, I couldn’t discover this goal within the newest ExpressLRS Configurator, so I didn’t replace the firmware however set the binding phrase within the Net UI.

Betaflight Configuration

Establishing Betaflight for maiden flight was easy.

The CineBot25 comes with Betaflight 4.5.0. The flight controller goal is TAKERG4AIO. Yow will discover the unique CLI diff right here (hyperlink to be added).

  • In Preset tab, apply ExpressLRS Preset based mostly on the packet fee of your selection.
  • In PID Tuning tab, set your personal charges.
  • In Modes tab, assign swap for arming.
  • In OSD tab, configure OSD parts. Though HD was chosen, the canvas was caught in analog dimension. I needed to de-select and choose HD once more to get the bigger HD OSD canvas.


I’m blown away by the GEPRC CineBot25 S—it has probably the greatest design available on the market, and the flight efficiency is superb! Whereas there are just a few hurdles to beat throughout setup, these are usually not deal breakers. Should you’re in search of a 2.5-inch cinewhoop for the DJI O3 system, that is the one I’d suggest proper now.

Get the GepRC Cinebot25 from these distributors:

Get some Lava 4S 850mAh batteries:

Get some spare propellers:

Geprc Cinebot25 S Cinewhoop Front

Nonetheless, this drone isn’t designed for sub-250 grams in thoughts. You might most likely push it underneath 250 grams by going analog or utilizing a smaller battery, however you’d be higher off with a 2-inch quad as a substitute (try the Pavo20). I additionally don’t suggest utilizing a GoPro on the CineBot25; it kills its flight efficiency and flight time. If you wish to use a GoPro, go for a 3-inch or 3.5-inch quad.

For cinematic FPV flying and dynamic pictures utilizing the O3, the CineBot25 S presents implausible design and efficiency at a good worth level. With its highly effective motors and DJI O3 compatibility, it stands out as a robust contender within the cinewhoop market.

Leave a Reply

Your email address will not be published. Required fields are marked *